Install MotionEyeOS on Raspberry Pi. It supports most USB cameras, Raspberry Pi camera modules. You’ll install MotionEyeOS on a microSD card and then.

Ensure your webcam is plugged into the usb port on your Raspberry Pi and start the service: $ sudo service motion start If you want to stop the service then use the command: $ sudo service motion stop With the service started you can now open a webpage on your normal computer and by going to the IP of the Raspberry pi on port 8081 (in the address bar) you should be able to view your webcam (please note that the one in the picture shows port 8089 as I have set this up in the conf file. The default port is 8081): 192.168.1.105:8081 I hope you have enjoyed this instructable and in the near future I will do a guide to allow you to view your webcam over the internet. The reason I have this is so I can connect my webcam to the eye piece of my telescope and transmit my astroviews over the web so friends and family can see the galaxy. Try to reboot. It sometimes helps. Check you don't have a firewall blocking the port if you access from another computer. Sudo service ufw disable But you also might want to try directly on first with localhost:8081 Another port is provided for control localhost:8080 If that works check if the port is not redirected by a router in your network You can edit the motion.conf file and change to another port.

Don't forget to start/stop the motion daemon after the change. Does you webcam works with other software? Try lsusb lsusb and see if your hardware is detected You should see something similar: Bus 001 Device 004: ID 046d:082b Logitech, Inc.

Webcam C170 For some help see that page on the webcam section. For the life of me I can not get this to work. I have followed the instructions to a T.

Download UKTS 1.32 Full Version + Mod Pack Indonesia + CRACK via Google Drive & Dropbox. Sya mau free download ukts busmod indonesia di hp Android,, cara yg mudah downloadnya bagaimana? Kalau mau main game bus silahkan download aja Indonesia Bus Simulator di playstore, itu juga bagus kok gameplay nya. Download Bus Simulator Indonesia (UKTS 1.32 + MOD) Updated on February 21, 2014 by Hienzo 31 Comments Dengan tambahan mod versi indonesia, suasana bermain akan tambah seru, karena anda tidak harus mengantar cargo lagi dan mencoba sebagai supir bus yang mengangkut penumpang. Download UKTS 1.32 + Mod Indonesia hay sobat, kali ini saya akan memberikan suatu game yang sangat seru di mainkan,bisa di mainkan dengan map indonesia, game ini adalah UK Truk Simulator. Gak usah basa basi lagi, cekidot. Download Bus Simulator Indonesia UKTS & Mod yang bisa di mainkan di PC dengan versi Terbaru. Game lawas ini ternyata masih populer mungkin karena Gameplay nya sangat bermanfaat sekali untuk kita yang dapat berlatih mengederai sebuah Bus. Free download ukts bus mod indonesia full version.

I have a logitech c310 which I see in lsusb so I know it's there. I finish the instructions and run sudo service motion start. Nothing happens.

I figure maybe I should reboot the pi. It comes back up.

And the daemon appears to kick in. Lights on the cam!!!then a few seconds after the raspberry is back up and again nothing. Tamil book publishers.

Sudo service motion start yields no results. I have the files edited correctly, and even turned localhost off for both streaming and management but 8080 and 8081 show nothing. Other options? I had the same problem and, like others in this thread, noticed that the webcam turned off when motion was detected.

The motion config file is set to save pictures when motion is detected. Since I didn't want to store photos nor videos, I disabled these options by setting output_pictures off and ffmpeg_output_movies off in the config file. This allowed the camera to stream without a problem. Jarrad's solution to give permissions to the directory would probably work if you wanted to store pics/videos. Thanks Ricardo. I've been going through so many pages for the past hour because the webcam stopped streaming after a few seconds. Your fix is working for me.

And what JarradD2 below said made sense. 'Motion' module doesn't have permission to save photos/videos. I don't know how to give permission so I'm following your route. Folks, if you want this to work, make sure you got the following settings correct for /etc/motion/motion.conf: output_pictures off (default on) ffmpeg_output_movies off (default on) stream_localhost off daemon on stream_maxrate 100 framerate 100 weight xxx height xxx webcam_localhost is an outdated variable. The new one is now called stream_localhost.